50TPD soybean oil refinery plant

Shandong Leader Machinery Co.,ltd. have engaged in Oil Refinery Equipment and Microwave Equipment since1997 in China,with 20 years` experience and 80 engineers,, scientific research, manufacturing, installation, commissioning.We can provide customers with design and services of 1-2000 tons oil equipment.factory occupied area is over 100,000 square meters,more than 3200 customers all around the world, we greatly hope to have the opportunity to serve you.

Shandong Leader Machinery Co.,ltd. has finished hundreds of successful projects over the years: peanut oil, soybean oil, rapeseed oil, cottonseed oil, sunflower oil, sesame oil, animal oil,grape seed oil, acer truncatum oil, peony seed oil, walnut oil, hemp seed oil, pine oil, tea seed oil, papaya oil, milk thistle seed, and other special type oil.We have independent import and export department. Our equipment has been successfully exported to more than 100 countries: Russia, Australia, India, Afghanistan, Cameroon,and so on.

My Phone: 15515503052

Skype:lisa-qe

Company Website: www.hnqely.com

Company Name: LD and Oil Machinery Co., Ltd.

1. 50TPD soybean oil refinery plant Main refining process:

(1).P-acid degumming operation:

Drawing the filtered or settled crude oil into the neutral pot, control oil temperature 40 ° C, liquid level cover the neutral pot volume about 80 %.Add into the neutral pot P-acid with 85% concentration, 0.1-0.2% oil weight.Start

up neutral pot, make main shalf stirring at 60-70 r/min, finish de-gumming in 30 min.

(2)alkali de-acid operation:

After finish de-gumming process, at once add into lye carrying alkali refining deacid, lye concentration 16 ° Be ′,

super alkali is 0.1-0.3% oil weight, af-ter finish adding, continuous stirring 30min, when soap particles accumulated

condensing, should reduce stirring speed, 30r/min avoid emulsion. After adding alkali, gradually rising temp

to the end temp 65 ° C, see to that the rising temp speed should control at 1 degree per minute, not too fast.

Shut off neutral pot drive part, the oil settled in the pot 6-8 hours, make oilseparate from soap.

(3)water rinse operation:

Adjust the neutral pot oil temp to about 85 ° C, add into hot water whose temp higher oil temp 10-15° C, the water use

amount each time is 10-15% oil weight.Start neutral pot drive part, make the main shalf stirring washing at 30r/m-

in, make the oil and water fully contact, stirring time 5-10 min.If oil/soap separate not ideal, the oil contains relative

high left soap, the first time washing, better to use thin salt water evenly spray into oil.

(4).de-coloring:

After dehydrate, inhale 3-5% oil weight active clay into the de-color pot to carry absorb de-coloring.

Decolor pot main axis stirring speed 60r/min, time 20 min, vacuum degree 750mmHg, is the whole absorb decolor craft

process requirement. Shut off vacuum valve, open vacuum break valve, stirring non-stop, reduce the oil temp down

to 70 ° C, the de-color finished.Continuous stirring, open oil outlet valve, press the de-color oil into the press filter, filter away waste clay, the last use air compressor blow clean and dry

(5).De-odor operation:

Open the vacuum valve, make the pot inside vacuum degree gradually reach above 750mmHg.

Inhale the de-color oil after filter into the de-odor pot, see to that oil amount should

cover the pot volume 60% Control oil temp at 240 ° C - 260 ° C, use the direct steam

under 0.1 -0.3Mpa to distillate 3-4 hours.

Shut off steam, shut off heat source, when the oil temp cooling to below 80 ° C, shut off vacuum, release de-odor oil , the de-odor process has finished.

Until now, the product oil after de-odor is high cooking oil, there are some factories

carrying again one time fine filtering after de-odor to increase the oil qulity.

The salad oil refining process is same to the high cooking oil refining proc ess, just has

a little higher requirements in each section, for example, during alkali refining, the super amount alkali a little much, when de-coloring, the bleaching agent much, de-odor time properly longer, the temp relatively higher, add one fine filtering section.

2. 50TPD soybean oil refinery plant Characteristics:

This units belongs to intermittent refining oil equipment, has all functions of large, small scale intermittent refining

equipment, and better than them. This equipment can produce high-cooking oil or salad oil. This units complete set

combined, self-prepare heat source, gas source, elect-rics control.

Light weight, save electricity , convenient use, this machine do not need special basis, either indoor

or outdoor is OK, just need to make up power source, water, prepare coal, alkali, Pacid, active clay, edible salt and other consume materials.

3. 50TPD soybean oil refinery plant Units devices:

(1). Refining pot: used to P-acid de-gumming, alkali refining de-acid and water rinsing.

(2).De-color pot: used to remove off pigments, bleaching oils and grease de-hydrate.

(3).De-odor pot: used to remove off oils odor, foreign smells (stainless made)

Heat-transfer oil stove: supply each device production needing heat energy, temperature reach

above 280 ° C.

(4).Steam generator: produce the needing steam for de-odoring and distillation.

(5).Vacuum pump: supply needing vacuum for dehydrate, de-color, de-odor. Vacuum degree

can reach above 755mmHg.

(6).Press filter: filter clay, filter out clear oil.

(7).Air compressor: blow dry bleached clay, blow empty the leftover oil in the press filter.

4. 50TPD soybean oil refinery plant Parameters:

Our comapny

Our Factory

Customers visit our factory

CE certification (safe certification) and

BV certification.(quality certification)

Contact information

The refining section main parts of 50TPD soybean oil refinery plant:
1. Deacidification tank, used for acid refining, alkali refining and hydration
2. Bleaching pot, used for removing off pigments, bleaching oils and grease dehydrate
3. Deodorization pot, used for removing fatty acid and other rare delicacy high efficiently
AAA1

Leaching Section Processing of 50tpd soybean oil refinery plant:
1. The material (for pretreatment) is sent to rotary extraction by the scraper conveyor. The material will extracted by the solvent or mix oil. After this step, we will get meal and mix oil.
2. Meal is sent to toaster. Through the toaster, the solvent in the meal will separate from the meal. The solvent goes to condenser and is recycled to rotary extractor.

AAA2

If you have any demand about microwave drying equipment and edible oil refining equipment, pls feel free contact us any time.

LD Miss Candy
Skype: leaderfoodmachine9
Mobile: +86 18363700691 (Also WhatsApp & Wechat)
Email: [email protected]