palm oil processing machines in Ghana

Specifications

palm oil processing machines

Reception station:

A, The FFB bunch be transported to plant by truck, after be weighted by weighting bridge, the FFB will be loaded down to FFB Loading Ramp.

B, The iron door of unloading ramp is controlled by hydraulic device, Get the power from Hydraulic pump station. Start on the hydraulic device, iron door be lifted. FFB will fall down to the Palm Fruit screw conveyor, be transported to pre-treatment plant, to Vertical sterilizer.

Sterilizing process:

A, By Scraper Conveyor, FFB be transported to the top of sterilizing tank. Falling into sterilizing tank from feed inlet.

B, Sterilizing tank: The inside diameter of sterilizing tank is φ2000mm, length 12500mm, welded up by Q235B material (Chemical composition:C0.12~0.2%,Si0.12~0.3%,Mm0.3~0.7%,P

C, After FFB be transported into sterilizing tank (202), close the door of sterilizing tank, and open the vent valve behind the tank, then saturated steam, which pressure is 3bar and temperature is about 130°C. After all the cooling air have been discharged out,close vent valve, proceed to sterilizing section. Sterilizing time is 55~60minutes.

D, The time of sterilizing is also according the kind of FFB, if the pressure is too high or the time is too long , palm fruit will be rot, also Resulting in the loss of oil, high temperature can change palm color.

E, Finish sterilizing process, close the steam valve, open the valve lead to Blow-off/down Silencer, can’t open the sterilizing tank door until discharges out all steam and water.

F, Open the sterilizing tank door, sterilized FFB will fall on the FFB Scraper conveyor. Be transported to next station.

Threshing station:

A, The sterilized FFB will be transport to thresher platform by scraper conveyor.

B, We adopt advanced Drum type thresher, insider diameter is φ1800mm, length is 5000mm.The material of main shaft is #45 steel (main chemical composition is C0.42~0.50%, Si0.17~0.37%, Mm0.50~0.30%, P≤0.035%, S≤0.035%, Cr≤0.25%, Ni≤0.25%, Cu≤0.025%).

C, Sterilized FFB be twisted and knocked in thresher. Palm fruit will be separated from empty bunch totally, fall on Fruit Scraper conveyor though fence, the empty bunch will be transported to Bunch Temporary tank by Bunch Scraper conveyor.

palm oil machine press:

A, The palm fruit is transported to Crush tank (401) by fruit elevator.

B, The fruit in crush tank will be heated to 90~95°C, crush time is 10~20 minutes.

C, The pounded fruit flow into Palm fruit oil presser(402) to press. Oil press cone can control cylinder, working pressure is 50~70bar, revolving speed of presser main shaft is 12.5 r/min. Meanwhile the mixture of crude palm oil and water outflow from barrel holes. Crude oil will be flow in Temporary Storage oil tank(T06) through crude oil groove. Then oil will be pumped to Screening filter(601) by oil pump. After filtering take out the oil foam, deposit impurities. Palm oil flow into Passivating oil tank(602). The fiber cake and nucleus are exhausted from clearance of cone head drop on Breaking cake auger (501).

D, Palm fruit oil presser (402), the material of main shaft is 40Cr steel, (Chemical component: C0.37~0.44%,Si0.17~0.37%, Mn0.50~0.80%,Cr0.80~1.10%) have been thermal refining, the material of worm and cone head is 45# Cast-Steel, and the surface have quenching treatment.

Kernel recovery system:

Sewage treatment:

Our Warm Professional Advice:

If you like our products,please kindly tell us your requirements,includes raw material name ,your processing capacity per day, have the production plant or not and related data, then we can efficiently make a cost-effective plan for you, we can calculate the cost and profit for you. Your trust and support are our large success.

Oil refining means separating impurity from oil based on the different characteristics of oil and impurity, in order to enhance the stability and security of oil. Oil refining including two technologies, physical refining and chemical refining.echnological process details of palm oil processing machines in Ghana:
AAA1

1. Acid reaction process
Oil temperature can be adjusted by screw plate heat exchanger. When the temperature is heated to about 80℃, mixing about 85% food grade phosphoric acid into acid reaction tank for reacting. In the tank, most non-hydrated phospholipid transfer into hydrated phospholipid.
AAA1

2. Neutralization process
In the neutral section, degummed oil with appropriate temperature and the appropriate concentration of alkali liquor, into the neutralization centrifugal mixer mixing, in order to achieve the effect of mixed, the mixture is then sent to neutralization tank for enough time, in this process, excessive alkali neutralization of free fatty acids and some phosphate form soapstock , after pumping oil soap mixture into heater oil heating to 85 ~ 90 ℃ in centrifuge separation oil - soap (or oil - glue). Oil soapstock of the separated (or foot) feet into the oil tank, and then to the salting out with soap pump tank isolated part of the oil.
AAA2

3. Washing process
Neutral oil from separator, still contains about 500 ppm soap, in order to reduce the residual content of soap, oil is joined by about 10% of hot water, washed in the washing mixer, hot water will absorb oil soap and other impurities, then in the water separator are separated.

AAA3

If you have any demand about microwave drying equipment and edible oil refining equipment, pls feel free contact us any time.

LD Miss Candy
Skype: leaderfoodmachine9
Mobile: +86 18363700691 (Also WhatsApp & Wechat)
Email: [email protected]

Shandong Leader Machinery Co.,ltd. is a microwave equipment, microwave drying sterilization machine, microwave heating equipment, microwave drying machine, microwave sterilization equipment, microwave drying equipment, whole s microwave curing equipment, microwave drying sterilization condiment, Shandong microwave drying Machine, melon seeds microwave dryer and other products specializing in the production and processing company, has a complete and scientific quality management system. Shandong Leader Machinery Co.,ltd.integrity, strength and quality of products recognized by the industry.

Why do you choose the Shandong Leader Machinery Co.,ltd. palm oil processing machines in Ghana?
1.Healthy! Pure mechanical squeezing craft maximally keeps the nutrients of the oil plants.No chemical substances left
2. High working efficiency! Due to a high working efficiency of the screw oil press machinery,both time and power can be saved.
3. Long durability! All the parts are made of the most suitable material and treated with refined crafts, such as cemented quenching and tempering to increase the hardness, consequently the durability.
4. palm oil processing machines in GhanaCost-effective! Low investment! The wearing parts on the oil press machinery such as the squeeze loop, squeeze spiral and squeeze bar are designed to be dismountable. When they are out of service period, users only need to replace them and there is no need to displace the whole machine.